View R1114D401D-TR-FE_9079114.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

r1114x series low noise 150ma ldo regulator no.ea-094-111026 1 outline the r1114x series are cmos-based voltage regulator ics with high output voltage accuracy, low supply current, low on-resistance, and high ripple rejection. each of these ics consists of a voltage reference unit, an error amplifier, resistor-net for voltage setting, a current limit circuit, and a chip enable circuit. these ics perform with low dropout voltage and a chip enable function. the line transient response and load transient response of the r1114x series are excellent, t hus these ics are very suitable for the power supply for hand-held communication equipment. the output voltage of these ics is fixed with high accuracy. since the packages for these ics are sot-23-5, sc-82ab, and son1612-6 therefore high density mounting of the ics on boards is possible. features ? supply curre nt ..................................................................... typ. 75 a ? standby mode ...................................................................... typ. 0.1 a ? dropout voltage ................................................................... typ. 0.22v (i out =150ma 3.0v output type) ? ripple rejectio n................................................................... typ. 70db (f= 1khz 3.0v output type) typ. 60db (f = 10khz) ? temperature-drift coefficient of output voltage .................. typ. 100ppm/ c ? line regulation .................................................................... typ. 0.02%/v ? output voltage range.......................................................... 1.5v to 4.0v (0.1v steps) ( for other voltages, please refer to mark informations.) ? output volt age accuracy...................................................... 2.0% ? packages ............................................................................ son1 612-6, sc-82ab, sot-23-5 ? built-in fold back protection circuit .................................... typ. 40ma (c urrent at short mode) ? ceramic capacitors are recommended to be used with this ic ... c in = c out = 1 f (v out <2.5v) c in = 1 f, c out = 0.47 f (v out > = 2.5v) applications ? power source for portable communication equipment. ? power source for electrical appliances such as cameras, vcrs and camcorders. ? power source for battery-powered equipment.
r1114x 2 block diagrams r1114xxx1a r1114xxx1b vref current limit v dd 15 2 3 v out gnd ce v out gnd v dd ce vref current limit + - r1114xxx1d v out gnd v dd ce vref current limit + -
r1114x 3 selection guide the output voltage, auto discharge functi on, package, and the taping type, et c. for the ics can be selected at the user?s request. product name package quantity per reel pb free halogen free r1114dxx1 ? -tr-fe son1612-6 4,000 pcs yes yes r1114qxx1 ? -tr-fe sc-82ab 3,000 pcs yes yes r1114nxx1 ? -tr-fe sot-23-5 3,000 pcs yes yes xx : the output voltage can be designated in the rang e from 1.5v(15) to 4.0v(40) in 0.1v steps. (for other voltages, please refer to mark informations.) ? : ce pin polarity and auto discharge functi on at off state are options as follows. (a) "l" active, without auto discharge function at off state (b) "h" active, without aut o discharge function at off state (d) "h" active, with auto discharge function at off state
r1114x 4 pin configuration z son1612-6 z sc-82ab z sot-23-5 1 2 3 6 5 4 12 3 4 (mark side) 1 4 5 2 3 (mark side) pin descriptions x r1114d pin no. symbol description 1 v dd input pin 2 gnd ground pin 3 v out output pin 4 nc no connection 5 gnd ground pin 6 ce or ce chip enable pin x r1114q pin no. symbol description 1 ce or ce chip enable pin 2 gnd ground pin 3 v out output pin 4 v dd input pin x r1114n pin no. symbol description 1 v dd input pin 2 gnd ground pin 3 ce or ce chip enable pin 4 nc no connection 5 v out output pin
r1114x 5 absolute maximum ratings symbol item rating unit v in input voltage 6.5 v v ce input voltage ( ce or ce pin) 6.5 v v out output voltage ? 0.3~v in + 0.3 v i out output current 200 ma power dissipation (son1612-6) ? 500 power dissipation (sc-82ab) ? 380 p d power dissipation (sot-23-5) ? 420 mw topt operating temperature range ? 40~85 c tstg storage temperature range ? 55~125 c ? ) for power dissipation, please refer to package information. absolute maximum ratings electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent damages and may degrade the life time and safety for both device and sy stem using the device in the field. the functional operation at or over these absolute maximum ratings is not assured. recommended operating conditions (electrical characteristics) all of electronic equipment should be designed that the mounted semiconductor devices operate within the recommended operating conditions. the semiconductor devices cannot operate normally over the recommended operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. and the semiconductor de vices may receive serious damage when they continue to operate over the recommended operating conditions.
r1114x 6 electrical characteristics ? r1114xxx1a topt = 25 c symbol item conditions min. typ. max. unit v out output voltage v in = set v out + 1v 1ma < = < = 0.980 1.020 v i out output current v in ? v out = 1.0v 150 ma v out / i out load regulation v in = set v out + 1v 1ma < = < = = set v out + 1v, i out = 0ma 75 95 a istandby supply current (standby) v in = set v out + 1v v ce = v dd 0.1 1.0 a v out / v in line regulation v out > 1.7v, set v out + 0.5v < = < = < = v in < = = 30ma 0.02 0.10 %/v rr ripple rejection f = 1khz f = 10khz ripple 0.5vp ? p v out > 1.7v, v in ? v out = 1.0v v out < = ? v out = 1.2v i out = 30ma 70 60 db v in input voltage 2.0 6.0 v v out / t opt output voltage temperature coefficient i out = 30ma ? 40 c < = < = c 100 ppm / c i sc short current limit v out = 0v 40 ma r pu ce pull-up resistance 0.7 2.0 8.0 m v ceh ce input voltage ?h? 1.5 6.0 v v cel ce input voltage ?l? 0.0 0.3 v en output noise bw = 10hz to 100khz 30 vrms
r1114x 7 ? r1114xxx1b/d topt = 25 c symbol item conditions min. typ. max. unit v out output voltage v in = set v out + 1v 1ma < = < = 0.980 1.020 v i out output current v in ? v out = 1.0v 150 ma v out / i out load regulation v in = set v out + 1v 1ma < = < = = set v out + 1v, i out = 0ma 75 95 a istandby supply current (standby) v in = set v out + 1v v ce = gnd 0.1 1.0 a v out / v in line regulation v out > 1.7v, set v out + 0.5v < = < = < = v in < = = 30ma 0.02 0.10 %/v rr ripple rejection f = 1khz f = 10khz ripple 0.5vp ? p v out > 1.7v, v in ? v out = 1.0v v out < = ? v out = 1.2v i out = 30ma 70 60 db v in input voltage 2.0 6.0 v v out / t opt output voltage temperature coefficient i out = 30ma ? 40 c < = < = c 100 ppm / c i sc short current limit v out = 0v 40 ma r pd ce pull-down resistance 0.7 2.0 8.0 m v ceh ce input voltage ?h? 1.5 6.0 v v cel ce input voltage ?l? 0.0 0.3 v en output noise bw = 10hz to 100khz 30 vrms r low on resistance of nch for auto-discharge (only for d version) v ce = 0v 60
r1114x 8 ? electrical characteristics by output voltage topt = 25 c dropout voltage v dif (v) output voltage v out (v) condition typ. max. v out = 1.5 0.38 0.70 v out = 1.6 0.36 0.65 v out = 1.7 0.34 0.60 1.8 < = v out < = 2.0 0.32 0.55 2.1 < = v out < = 2.7 0.28 0.50 2.8 < = v out < = 4.0 i out = 150ma 0.22 0.35 technical notes when using these ics, consider the following points: phase compensation in these ics, phase compensation is made for securing st able operation even if the load current is varied. for this purpose, use a capacitor c out with good frequency characteristics and esr (equivalent series resistance). (note: if additional ceramic capacitors are connected with parallel to the output pin with an output capacitor for phase compensation, the operation might be unstable. becaus e of this, test these ics with as same external components as ones to be used on the pcb.) pcb layout make v dd and gnd lines sufficient. if their impedance is hi gh, noise pickup or unstable operation may result. connect a capacitor with a capacitance value as much as 1.0 f or more between v dd and gnd pin, and as close as possible to the pins. set external components, especially t he output capacitor, as close as possi ble to the ics, and make wiring as short as possible.
r1114x 9 test circuits ce v out out gnd 1.0 f 1.0 f v dd in r1114xxx1b/d series i out ce v out out gnd 1.0 f 1.0 f v dd in r1114xxx1b/d series i ss fig.1 standard test circuit fig.2 supply current test circuit ce v out out gnd 1.0 f v dd in r1114xxx1b/d series i out p .g. ce v out out gnd i1 i2 1.0f 1.0 f v dd in r1114xxx1b/d series fig.3 ripple rejection, line transient fig.4 load transient response test circuit response test circuit
r1114x 10 typical applications r1114nxx1a series v out out in v dd gnd ce cap. cap. + + r1114xxx1b series v out out in v dd gnd ce cap. cap. + + (external components) output capacitor; ceramic 0.47 f (set output voltage in the range from 2.5 to 4.0v) ceramic 1.0 f (set output voltage in the range from 1.5 to 2.4v) input capacitor; ceramic 1.0 f typical characteristics 1) output voltage vs. output current (topt = 25 c) r1114x151x r1114x281x 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 output current i out (ma) output voltage v out (v) 0 400 300 200 100 2.5v 1.8v 2.0v v in =3.5v 3.0 2.5 2.0 1.5 1.0 0.5 0.0 output current i out (ma) output voltage v out (v) 0 400 300 200 100 3.5v 3.8v 3.1v v in =4.8v r1114x401x 4.5 3.5 4.0 3.0 2.0 2.5 1.5 1.0 0.5 0.0 output current i out (ma) output voltage v out (v) 0 400 300 200 100 4.5v 5.0v 4.3v v in =6.0v
r1114x 11 2) output voltage vs. input voltage (topt = 25 c) r1114x151x r1114x281x 1.7 1.3 1.4 1.5 1.6 1.1 1.2 1.0 input voltage v in (v) output voltage v out (v) 16 45 32 i out =1ma i out =30ma i out =50ma 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2.0 26 5 4 3 input voltage v in (v) output voltage v out (v) i out =1ma i out =30ma i out =50ma r1114x401x 4.2 4.0 3.6 3.2 3.8 3.4 3.0 2 16 543 input voltage v in (v) output voltage v out (v) i out =1ma i out =30ma i out =50ma 3) supply current vs. input voltage (topt = 25 c) r1114x151x r1114x281x 70 60 90 80 50 40 30 20 10 0 supply current i ss (a) 21 06 543 input voltage v in (v) 70 60 90 80 50 40 30 20 10 0 21 06 543 supply current i ss (a) input voltage v in (v)
r1114x 12 r1114x401x 70 60 90 80 50 40 30 20 10 0 21 06 543 supply current i ss (a) input voltage v in (v) 4) output voltage vs. temperature r1114x151x r1114x281x 1.53 1.52 1.51 1.50 1.49 1.48 1.47 1.46 temperature topt(c) output voltage v out (v) 10-15 -40 856035 2.86 2.80 2.78 2.76 2.84 2.82 2.74 10-15 -40 856035 temperature topt(c) output voltage v out (v) r1114x401x 4.08 4.06 4.04 4.02 4.00 3.98 3.96 3.94 3.92 10-15 -40 856035 temperature topt(c) output voltage v out (v)
r1114x 13 5) supply current vs. temperature r1114x151x r1114x281x 90 80 70 60 50 40 30 20 10 0 temperature topt(c) supply current i ss (a) 10-15 -40 856035 90 80 70 60 50 40 30 20 10 0 supply current i ss (a) 10-15 -40 856035 temperature topt(c) r1114x401x 90 80 70 60 50 40 30 20 10 0 10-15 -40 856035 supply current i ss (a) temperature topt(c) 6) dropout voltage vs. temperature r1114x151x r1114x161x 0.6 0.5 0.4 0.3 0.2 0.1 0.0 output current i out (ma) dropout voltage v dif (v) 50250 15012510075 85c 25c -40c 0.6 0.5 0.4 0.3 0.2 0.1 0.0 50250 15012510075 output current i out (ma) dropout voltage v dif (v) 85c 25c -40c
r1114x 14 r1114x171x r1114x181x 0.6 0.5 0.4 0.3 0.2 0.1 0.0 50250 15012510075 output current i out (ma) dropout voltage v dif (v) 85c 25c -40c 0.6 0.5 0.4 0.3 0.2 0.1 0.0 50250 15012510075 output current i out (ma) dropout voltage v dif (v) 85c 25c -40c r1114x211x r1114x281x 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 50250 15012510075 output current i out (ma) dropout voltage v dif (v) 85c 25c -40c 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 50250 15012510075 output current i out (ma) dropout voltage v dif (v) 85c 25c -40c r1114x401x 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 50250 15012510075 output current i out (ma) dropout voltage v dif (v) 85c 25c -40c
r1114x 15 7) dropout voltage vs. set output voltage (topt = 25 c) 0.60 0.40 0.50 0.20 0.10 0.30 0.00 set output voltage v reg (v) dropout voltage v dif (v) 2.01.51.0 4.03.53.02.5 10ma 30ma 50ma 150ma 8) ripple rejection vs. input bias voltage (topt = 25 c, c in = none, c out = ceramic0.47 f) r1114x281x r1114x281x 90 70 80 50 60 30 40 10 20 0 input voltage v in (v) ripple 0.2vp-p, i out =1ma ripple rejection rr(db) 3.0 2.9 3.3 3.2 3.1 f=1khz f=10khz f=100khz 90 70 80 50 60 30 40 10 20 0 ripple 0.5vp-p, i out =1ma 3.0 2.9 3.3 3.2 3.1 input voltage v in (v) ripple rejection rr(db) f=1khz f=10khz f=100khz r1114x281x r1114x281x 90 70 80 50 60 30 40 10 20 0 ripple 0.2vp-p, i out =30ma 3.0 2.9 3.3 3.2 3.1 input voltage v in (v) ripple rejection rr(db) f=1khz f=10khz f=100khz 90 70 80 50 60 30 40 10 20 0 ripple 0.5vp-p, i out =30ma 3.0 2.9 3.3 3.2 3.1 input voltage v in (v) ripple rejection rr(db) f=1khz f=10khz f=100khz
r1114x 16 r1114x281x r1114x281x 90 70 80 50 60 30 40 10 20 0 ripple 0.2vp-p, i out =50ma 3.0 2.9 3.3 3.2 3.1 input voltage v in (v) ripple rejection rr(db) f=1khz f=10khz f=100khz 90 70 80 50 60 30 40 10 20 0 ripple 0.5vp-p, i out =50ma 3.0 2.9 3.3 3.2 3.1 input voltage v in (v) ripple rejection rr(db) f=1khz f=10khz f=100khz 9) ripple rejection vs. frequency (c in = none) r1114x151x r1114x151x 90 70 80 50 60 30 40 10 20 0 frequency f(khz) v in =2.5v dc +0.5vp-p, c out =ceramic 1.0 f 1 0.1 100 10 ripple rejection rr(db) i out =1ma i out =30ma i out =50ma 90 70 80 50 60 30 40 10 20 0 v in =2.5v dc +0.5vp-p, c out =ceramic 2.2 f 1 0.1 100 10 frequency f(khz) ripple rejection rr(db) i out =1ma i out =30ma i out =50ma r1114x281x r1114x281x 90 70 80 50 60 30 40 10 20 0 v in =3.8v dc +0.5vp-p, c out =ceramic 0.47 f 1 0.1 100 10 frequency f(khz) ripple rejection rr(db) i out =1ma i out =30ma i out =50ma 90 70 80 50 60 30 40 10 20 0 v in =3.8v dc +0.5vp-p, c out =ceramic 1.0 f 1 0.1 100 10 frequency f(khz) ripple rejection rr(db) i out =1ma i out =30ma i out =50ma
r1114x 17 r1114x401x r1114x401x 90 70 80 50 60 30 40 10 20 0 v in =5.0v dc +0.5vp-p, c out =ceramic 0.47 f 1 0.1 100 10 frequency f(khz) ripple rejection rr(db) i out =1ma i out =30ma i out =50ma 90 70 80 50 60 30 40 10 20 0 v in =5.0v dc +0.5vp-p, c out =ceramic 1.0 f 1 0.1 100 10 frequency f(khz) ripple rejection rr(db) i out =1ma i out =30ma i out =50ma 10) input transient response (i out = 30ma, c in = none, tr = tf = 5 s, c out = ceramic 0.47 f) r1114x151x 1.55 1.54 1.53 1.52 1.51 1.50 1.49 4 3 2 1 0 time t(s) output voltage v out (v) input voltage v in (v) 10 0 20 405060708090100 30 input voltage output voltage r1114x281x 2.85 2.84 2.83 2.82 2.81 2.80 2.79 6 5 4 3 2 1 0 10 0 20 405060708090100 30 time t(s) output voltage v out (v) input voltage v in (v) input voltage output voltage
r1114x 18 11) load transient response (tr = tf = 0.5 s, c in = ceramic 1.0 f) r1114x151x v in =2.5v, c out =ceramic 1.0 f 1.75 1.70 1.65 1.60 1.55 1.50 1.45 150 100 50 0 output current i out (ma) 20 4 8 10 12 14 16 18 20 6 time t(s) output voltage v out (v) output current output voltage r1114x151x v in =2.5v, c out =ceramic 2.2 f 1.75 1.70 1.65 1.60 1.55 1.50 1.45 150 100 50 0 20 4 8 10 12 14 16 18 20 6 output current i out (ma) time t(s) output voltage v out (v) output current output voltage r1114x281x v in =3.8v, c out =ceramic 0.47 f 3.05 3.00 2.95 2.90 2.85 2.80 2.75 150 100 50 0 20 4 8 10 12 14 16 18 20 6 output current i out (ma) time t(s) output voltage v out (v) output current output voltage
r1114x 19 r1114x281x v in =3.8v, c out =ceramic 1.0 f 3.05 3.00 2.95 2.90 2.85 2.80 2.75 150 100 50 0 20 4 8 10 12 14 16 18 20 6 output current i out (ma) time t(s) output voltage v out (v) output current output voltage r1114x281x v in =3.8v, c out =ceramic 2.2 f 3.05 3.00 2.95 2.90 2.85 2.80 2.75 150 100 50 0 20 4 8 10 12 14 16 18 20 6 output current i out (ma) time t(s) output voltage v out (v) output current output voltage 12) turn-on/off speed with ce pin (d version) r1114x151d (v in = 2.5v, c in = ceramic 1.0 f, c out = ceramic 1.0 f) 4 0 1 2 3 6 2 3 0 1 4 5 time t(s) ce input voltage v ce (v) output voltage v out (v) 50-5 25 10 15 20 v in i out = 0ma i out = 30ma i out = 150ma 4 0 1 2 3 6 2 3 0 1 4 5 500-50 450 100 150 200 250 300 350 400 time t(s) ce input voltage v ce (v) output voltage v out (v) v in i out = 0ma i out = 30ma i out = 150ma
r1114x 20 r1114x281d (v in = 3.8v, c in = ceramic 0.47 f, c out = ceramic 0.47 f) 4 0 -1 1 2 3 8 4 5 0 3 2 1 6 7 0 5 10 15 20 25 -5 time t(s) ce input voltage v ce (v) output voltage v out (v) v in i out = 0ma i out = 30ma i out = 150ma 4 0 -1 1 2 3 8 4 5 0 3 2 1 6 7 0 20406080 120 100 140 160 180 -20 time t(s) ce input voltage v ce (v) output voltage v out (v) v in i out = 0ma i out = 30ma i out = 150ma r1114x401d (v in = 5.0v, c in = ceramic 0.47 f, c out = ceramic 0.47 f) 8 6 4 2 0 -2 14 12 10 8 6 4 2 0 -2 0 5 10 15 20 25 -5 time t(s) ce input voltage v ce (v) output voltage v out (v) v in i out = 0ma i out = 30ma i out = 150ma 8 6 4 2 0 -2 14 12 10 8 6 4 2 0 -2 0 20 40 60 80 100 120 140 160 180 -20 time t(s) ce input voltage v ce (v) output voltage v out (v) v in i out = 0ma i out = 30ma i out = 150ma
r1114x 21 esr vs. output current when using these ics, consider the following points: in these ics, phase compensation is made for securing st able operation even if the load current is varied. for this purpose, use a capacitor c out with good frequency characteristics and esr (equivalent series resistance) of which is in the range described as follows: gnd v out ce v in v in i out esr r1114xxx1b/d s.a. ceramic cap. ceramic cap. spectrum analyzer measuring circuit for white noise; r1114xxx1b/d the relations between i out (output current) and esr of an output ca pacitor are shown below. the conditions when the white noise level is under 40 v (avg.) are marked as the hatched area in the graph. (note: if additional ceramic capacitors are connected to the output pin with output capacitor for phase compensation, the operation might be unstable. because of this, test these ics with as same external components as ones to be used on the pcb.) (1) v in = v out + 1v (2) frequency band: 10hz to 2mhz (3) temperature: ? 40 c to 25 c r1114x151x r1114x161x 100 10 1 0.1 0.01 load current i out (ma) 06 0 30 150 120 esr () 90 c in =ceramic 1.0 f, c out =ceramic 1.0 f 100 10 1 0.1 0.01 load current i out (ma) 06 0 30 150 120 esr () 90 c in =ceramic 0.47 f, c out =ceramic 0.68 f
r1114x 22 r1114x211x r1114x281x 100 10 1 0.1 0.01 load current i out (ma) 06 0 30 150 120 esr () 90 c in =ceramic 0.47 f, c out =ceramic 0.47 f 100 10 1 0.1 0.01 load current i out (ma) 06 0 30 150 120 esr () 90 c in =ceramic 0.47 f, c out =ceramic 0.47 f
http://www.e-devices.ricoh.co.jp/en/ 4bmft4vqqpsu0$?dft 3*$0)&-&$530/*$%&7*$&4$0 -5% )jhbtij4ijobhbxb0$?df *oufsobujpobm4bmft
)jhbtij4ijobhbxb 4ijobhbxblv 5plzp +bqbo 1ipof'by 3*$0)&6301& /&5)&3-"/%4
#7 4fnjdpoevdups4vqqpsu$fousf 1spg8),fftpnmbbo %+"ntufmwffo 5if/fuifsmboet 1ipof 3*$0)&-&$530/*$%&7*$&4,03&"$0 -5% ' )bftvoh#meh 5fifsbosp (bohobnhv 4fpvm ,psfb 1ipof'by 3*$0)&-&$530/*$%&7*$&44)"/()"*$0 -5% 3ppn /p#vjmejoh /p#jcp3pbe 1v%poh/fx%jtusjdu 4ibohibj 1fpqmft3fqvcmjdpg$ijob 1ipof'by 3*$0)&-&$530/*$%&7*$&4$0 -5% 5bjqfjp$?df 3ppn ' /p )fohzboh3e 5bjqfj$juz 5bjxbo 30$
1ipof'by ricoh is committed to reducing the environmental loading materials in electrical devices with a view to contributing to the protection of human health and the environment. ricoh has been providing rohs compliant products since april 1, 2006 and halogen-free products since april 1, 2012. halogen free 5ifqspevdutboeuifqspevdutqfdjpdbujpoteftdsjcfejouijtepdvnfoubsftvckfduupdibohfps ejtdpoujovbujpopgqspevdujpoxjuipvuopujdfgpssfbtpot tvdibtjnqspwfnfou5ifsfgpsf cfgpsf efdjejohupvtfuifqspevdut qmfbtfsfgfsup3jdpitbmftsfqsftfoubujwftgpsuifmbuftujogpsnbujpo uifsfpo 5ifnbufsjbmtjouijtepdvnfounbzopucfdpqjfepspuifsxjtfsfqspevdfejoxipmfpsjoqbsuxjuipvu qsjpsxsjuufodpotfoupg3jdpi 1mfbtfcftvsfupublfbozofdfttbszgpsnbmjujftvoefssfmfwboumbxtpssfhvmbujpotcfgpsffyqpsujohps puifsxjtfubljohpvupgzpvsdpvouszuifqspevdutpsuifufdiojdbmjogpsnbujpoeftdsjcfeifsfjo 5ifufdiojdbmjogpsnbujpoeftdsjcfejouijtepdvnfoutipxtuzqjdbmdibsbdufsjtujdtpgboefybnqmf bqqmjdbujpodjsdvjutgpsuifqspevdut5ifsfmfbtfpgtvdijogpsnbujpojtopuupcfdpotusvfebtb xbssbouzpgpsbhsboupgmjdfotfvoefs3jdpitpsbozuijseqbsuztjoufmmfduvbmqspqfsuzsjhiutpsboz puifssjhiut 5ifqspevdutmjtufejouijtepdvnfoubsfjoufoefeboeeftjhofegpsvtfbthfofsbmfmfduspojd dpnqpofoutjotuboebsebqqmjdbujpot p$?dffrvjqnfou ufmfdpnnvojdbujpofrvjqnfou nfbtvsjoh jotusvnfout dpotvnfsfmfduspojdqspevdut bnvtfnfoufrvjqnfoufud
5iptfdvtupnfstjoufoejohup vtf bqspevdujobobqqmjdbujposfrvjsjohfyusfnfrvbmjuzboesfmjbcjmjuz gpsfybnqmf jobijhimztqfdjpd bqqmjdbujpoxifsfuifgbjmvsfpsnjtpqfsbujpopguifqspevdudpvmesftvmujoivnbojokvszpsefbui bjsdsbgu tqbdfwfijdmf ovdmfbssfbdupsdpouspmtztufn usb$?ddpouspmtztufn bvupnpujwfboe usbotqpsubujpofrvjqnfou dpncvtujpofrvjqnfou tbgfuzefwjdft mjgftvqqpsutztufnfud
tipvmepstu dpoubduvt 8fbsfnbljohpvsdpoujovpvtf$?psuupjnqspwfuifrvbmjuzboesfmjbcjmjuzpgpvsqspevdut cvu tfnjdpoevdupsqspevdutbsfmjlfmzupgbjmxjuidfsubjoqspcbcjmjuz*opsefsupqsfwfoubozjokvszup qfstpotpsebnbhftupqspqfsuzsftvmujohgspntvdigbjmvsf dvtupnfsttipvmecfdbsfgvmfopvhiup jodpsqpsbuftbgfuznfbtvsftjouifjseftjho tvdibtsfevoebodzgfbuvsf psfdpoubjonfougfbuvsfboe gbjmtbgfgfbuvsf8fepopubttvnfbozmjbcjmjuz pssftqpotjcjmjuzgpsbozmpttpsebnbhfbsjtjohgspn njtvtfpsjobqqspqsjbufvtfpguifqspevdut "oujsbejbujpoeftjhojtopujnqmfnfoufejouifqspevduteftdsjcfejouijtepdvnfou 1mfbtfdpoubdu3jdpitbmftsfqsftfoubujwfttipvmezpvibwfbozrvftujpotpsdpnnfoutdpodfsojoh uifqspevdutpsuifufdiojdbmjogpsnbujpo

▲Up To Search▲

Price & Availability of R1114D401D-TR-FE

	To Download R1114D401D-TR-FE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .